Annie Sloane Chalk Paint & Waxes + Gilding Wax

I have learned that before painting a piece of furniture it is a good idea to test the paint color and finish on a piece of spare molding (or flat wood piece). This tutorial shows the basics of using Annie Sloan Chalk paint, light and dark waxes, and a gold gilding wax.


  • Annie Sloan’s Chalk Paint (“old ochre” is used in this tutorial)
  • Annie Sloan’s Soft Wax – Clear
  • Annie Sloan’s Soft Wax – Dark
  • Le Franc & Bourgeois Gilding Wax (“Classic” gold is used in this tutorial)
  • Natural bristle paint brush
  • Two wax brushes with flat head bristles. Use one for clear wax and one for dark wax
  • Painter’s tape
  • Molding or wood piece
  • Lint free cloth

STEP 1:  Paint Your Piece & Let Dry

The wonderful thing about the Annie Sloan paint is that there is no need to sand or prep your piece. My piece of spare moulding has rough patches. I did not sand them because it will be interesting to see how the dark and gilding waxes take to the textured areas later in the process.

Paint your piece and let dry. I like to use long even strokes so that it dries as even as possible.  This is a personal preference.  You will notice that drying time is fairly quick. Another plus for using Annie Sloan Chalk Paint!

Don’t expect anything near a glossy lacquer smooth finish once your paint is dry.  You will get a matte chalky finish if you do not apply any wax.  That may be the look you are going for but the piece will not be protected and may be vulnerable to stains and scratches.  With wax your piece will have a very subtle sheen.

STEP 2: Apply Clear Wax

Once your paint is dry, its time to break out the clear wax and your flat head bristle brush. Helpful hint:  If you plan to use clear and dark wax in the same project it is a good idea to designate one brush for clear wax and one brush for dark wax.

Step 3: Buff Your Piece

Using a soft, lint free cloth vigorously rub the wax INTO the entire piece.  Do not rub as if you are just trying to take it off. Actually buff it out and rub it into all crevices. Once it is buffed out your piece will have a very slight sheen but will not be overly shiny. It should not be sticky to the touch. If it is sticky that means you have applied too much wax. It might be very slightly tacky and that’s okay as it will dry.

*Once you have buffed out all the clear wax you can either stop here or you can add dark wax next depending on the look you are trying to achieve.

Step 4: Apply Dark Wax (optional step)

Tape off part of your sample piece with painters tape. I applied my tape to the middle of the moulding. The left side of the sample is now finished since it has been painted and waxed with the clear wax.  Next, we will apply dark wax on just the right hand side of the moulding piece.

Using your waxing brush start applying a small amount of the dark wax. At this point let your creativity take over.  Depending on your desired look you can apply as little or as much dark wax as you like.  However, I would strongly recommend you apply a light coat of dark wax and add more if you’d like.  But remember, its easier to add wax then to subtract. Or you can just apply a little on certain areas you want to highlight just as I did on the piece shown below.  It’s entirely up to you.

STEP 5:  Buff your piece

The process is the same as Step 3.

If your piece came out too dark or if you applied dark wax in an area you didn’t like, apply a tiny bit of clear wax. The clear wax will act as an eraser of sorts. But this only works if you applied the clear wax after you painted (as shown in Step 2). That is why its always important to add clear wax after you paint. If you add dark wax directly onto a freshly painted surface you won’t be able to remove it entirely should you want to lighten up your piece or remove the dark wax all together.

STEP 6: Remove Tape

Remove the painter’s tape. At this point it’s interesting to see how different a piece can look depending on the wax used. The dark wax is on the left side and the clear wax is on the right.

STEP 7: Apply Gilding Wax (optional)

I went one step further and decided to add a bit of gold gilding wax to highlight certain areas. I simply used my fingers to apply the wax where I wanted.  I am only familiar with this type of gilding wax and it is very easy to use. Plus I like the fact that it comes in other colors.  I did not apply any clear wax but it might be a good idea once the gilding wax has dried a bit.

Here is my finished piece with the dark wax and gold gilding. I did not sand my wood piece and I like how the paint accentuates the texture.

Step 7: Label Your Sample

When you are all done don’t forget to label the back of your sample with the paint and wax colors used. If you used a certain paint technique that’s great to note also. This will be great for future reference. 


3 thoughts on “Annie Sloane Chalk Paint & Waxes + Gilding Wax

    • Reviving Charm says:

      It’s best to apply a little of the gilding and build up to the finish you want. Unfortunately, its not very forgiving. If you want to remove it, you need to work quickly. I usually will buff off as much as I can immediately with a clean cloth and will also try to use Annie Sloan’s clear wax to help buff off any extra, if needed. Good luck!

Leave a comment...I love feedback!